1.濟南卷簾門在開啟和關閉時應具有到位的停止功能，且不應停止滑動。如果滑動距離大于50mm，應立即執行卷簾門的控制裝置和制動器，并仔細檢查和維修，直其正常工作。
1. Jinan roller shutter door shall have a stop function in place when opening and closing, and shall not stop sliding. If the sliding distance is greater than 50mm, immediately execute the control device and brake of the rolling shutter door, and carefully check and repair until it works normally.
2.卷簾門的百葉窗易生銹部位應定期進行維護、油漆和防腐處理。嚴禁重物或硬物撞擊外墻。
2. The easily rusty parts of the shutter of the rolling shutter door shall be regularly maintained, painted and anti-corrosion treated. It is strictly prohibited to strike the external wall with heavy objects or hard objects.
3.卷簾門運行時，如有較大振動或異響，應關閉檢查，并妨礙卷簾門正常啟閉的雜物。
3. When the rolling shutter door is running, if there is a large vibration or abnormal sound, it shall be closed for inspection, and the sundries that hinder the normal opening and closing of the rolling shutter door shall be removed.
4.伸縮門近梁座的上限應與承重架下端保持200mm以上的距離，以確保制動器停止時無對接。
4. The upper limit of the near beam seat of the telescopic door shall be kept more than 200mm away from the lower end of the bearing frame to ensure that there is no docking when the brake stops.
5.卷簾門安裝位置上端應有可靠的防火設施。卷簾門下端用作箱體或屋頂時，應在電機下端安裝一個可拆卸的活動蓋，并預留500-500mm的空間拆除檢修孔。

5. Reliable fire prevention facilities shall be provided at the upper end of the installation position of rolling shutter door. When the lower end of the rolling shutter door is used as a box or roof, a removable movable cover shall be installed at the lower end of the motor, and a space of 500-500mm shall be reserved to remove the manhole.
6.所有電控卷簾門的開啟和關閉方向應與開關箱的方向一致，特別是在試運行期間重新連接電源或外部輸入電源相線時，濟南卷簾門電機需要用手動裝置進行維修，卷簾門應放入門孔內。在1/2高度位置，打開電源并嘗試打開和關閉卷簾門。它可以正常使用，直到附加到說明。否則，會(huì )損壞蓋子，卷簾會(huì )向后滾動或與頂部齊平，導致泄漏。
6. The opening and closing directions of all electric control rolling shutter doors shall be consistent with the direction of the switch box, especially when reconnecting the power supply or external input power phase line during the trial operation, the motor of Jinan rolling shutter door needs to be repaired by manual device, and the rolling shutter door shall be placed in the entry hole. In the 1 / 2 height position, turn on the power and try to open and close the roller shutter door. It can be used normally until attached to the description. Otherwise, the cover will be damaged and the roller shutter will roll back or flush with the top, resulting in leakage.
7.卷簾門檢修時，操作人員應站在能看到卷簾門運行狀態的位置，否則可能發生事故和損壞。
7. During the maintenance of the rolling shutter door, the operator shall stand at the position where the running state of the rolling shutter door can be seen, otherwise accidents and damage may occur.
8.卷簾門及卷簾門機嚴禁接觸酸堿溶液，以免腐蝕門簾表面。
8. The rolling shutter door and rolling shutter door machine are strictly prohibited from contacting acid-base solution to avoid corroding the surface of the door curtain.
9.卷簾門機應定期(每年少兩次)檢查卷簾門的運行、滑動、傳動等部位，并根據需要及時加油，確保卷簾門的正常使用。
9. The rolling shutter door machine shall regularly (at least twice a year) check the operation, sliding, transmission and other parts of the rolling shutter door, and timely refuel as required to ensure the normal use of the rolling shutter door.