調試是電動卷簾門安裝的一個過程，也是重要的一個過程，調試精 確對今后的運用都起到了決定性的效果。濟南卷簾門廠家為咱們講講怎么對電動門進行結構調試，仔細看哦!

Debugging is not only a process of the installation of the electric rolling shutter door, but also an important process. The accurate debugging has played a decisive role in the future application. Jinan roller shutter door manufacturers tell us how to debug the structure of the electric door, look carefully!

1、調試前的準備工作

1. Preparation before commissioning

⑴電動門履行器已正確安裝。

(1) the actuator of electric door has been installed correctly.

⑵一切的螺絲，銜接器和電氣銜接是安 全的。

(2) all screws, connectors and electrical connections are safe.

⑶電氣銜接是正確的和正確實施接地和粘接。

(3) the electrical connection is correct and the correct implementation of grounding and bonding.

⑷履行組織和閥門處于良好狀態，手動自在沒有卡紙。

(4) the performance organization and valve are in good condition, and there is no paper jam.

⑸模仿指令，反應是正確的。

(5) imitate the command and the response is correct.

2、SIPOS電動履行器調試器

2. SIPOS electric executor debugger

⑴履行組織調整的信號，依據要求比減速。

(1) carry out the signal of organization adjustment and reduce the speed according to the requirements.

⑵相應的MCC抽屜在當地媒體上的操控面板，遙 控 器的按鈕一次或屢次，履行組織的事務形式，長途操控傳輸，本地參數設置和調試這三種形式之間切換。

(2) the corresponding MCC drawer switches between the control panel on the local media, the button on the remote control once or repeatedly, the organizational transaction form, long-distance control transmission, local parameter setting and debugging.

⑶挑選這種形式的參數設置和調試，有四個菜單(言語設置，調試，調查，確診)。言語設置：當您挑選所需的言語按回車鍵(通常是英語)，共有五種言語挑選(德語，英語，法語，西班牙語，意大利語)。

(3) to select this form of parameter setting and debugging, there are four menus (speech setting, debugging, investigation, diagnosis). Language settings: when you select the language you want, press enter (usually in English). There are five languages to select (German, English, French, Spanish, Italian).

⑷進入調試菜單，并輸入四位數的PIN碼(9044)，更改設置并封閉了閥門相關的參數，要害參數的顯現：速度，翻開速度，緊迫起飛的速度，緊迫翻開速度，封閉端方位的關斷形式，關斷形式，敞開的結尾方位，大扭矩關系，大開扭矩，扭矩毛病重復，上升時刻，直流制動，電機溫度保護，電機發熱，調整完畢的方位，記載的扭矩曲線。假如參數的改變，只需列出的參數顯現按回車鍵進入。按箭頭鍵來更改參數。

(4) enter the debugging menu, input the four digit PIN code (9044), change the setting and close the valve related parameters, and display the key parameters: speed, opening speed, urgent take-off speed, urgent opening speed, closing form of closed end orientation, closing form, opening end orientation, large torque relationship, large opening torque, repeated torque faults, rising time, DC braking, motor temperature protection, motor heating, adjusted position, recorded torque curve. If the parameter changes, just list the parameters to display, press enter to enter. Press the arrow keys to change the parameters.

⑸調整到的方位調整履行組織的行程限位。首要，設置的完畢方位或封閉。是敞開的，例如，依據恰當的執法組織，以敞開的健康運轉到完畢，按回車鍵兩秒鐘到達結尾的方位，在屏幕上顯現一個過錯，然后調整電位器，允許差錯為零。按恰當的鍵兩秒鐘，封閉運轉的履行組織的末端方位，然后按Enter。設置相應的屏幕顯現份額，顯現設置的完畢是正確的。

(5) adjust the position to fulfill the travel limit of the organization. First of all, set the end of the orientation or closed. It is open, for example, according to the appropriate law enforcement organization, with the open health running to the end, press the return key to reach the ending position in two seconds, showing a fault on the screen, then adjust the potentiometer, allowing the error to be zero. Press the appropriate key for two seconds to close the end position of the running fulfillment organization, and then press enter. Set the corresponding screen display share, and the display setting is correct.

⑹調整完畢的方位，依據本地/長途操作鍵，遠遠超越CRT屏幕顯現操作與脈沖測驗的靈敏度履行組織。

(6) according to the local / long-distance operation key, the orientation after adjustment is far beyond the sensitivity of CRT screen display operation and pulse test.