在感應玻璃門日常使用的過程中，常見的故障就是突然打不開了或者突然關不上了？遇到這種故障你知道如何辦嗎？今天門道佰分佰小編就根據平常維修感應玻璃門故障的經驗為大家總結了一些維修方法。希望對廣大感應玻璃門使用客戶有所幫助。

In the process of daily use of the induction glass door, the common fault is that it can not be opened or closed suddenly? Do you know what to do in case of such failure? Today, doorway baifenbai Xiaobian summarized some maintenance methods for you based on the experience of ordinary maintenance of induction glass doors. It is hoped that it will be helpful to customers who use induction glass doors.

檢查是否是感應玻璃門防夾功能在作怪，導致感應玻璃門打不開。

Check whether the anti pinch function of the sensing glass door is causing trouble, resulting in the non opening of the sensing glass door.

感應玻璃門機具有防夾功能，遇到障礙或感應玻璃門碰撞會(huì )導致感應玻璃門不能正常打開，在達到三次時，感應玻璃門將會(huì )停止運行，門扇會(huì )停止開門或關閉，遇到這種問題只需將門扇推完全打開狀態即可恢復。

The induction glass door machine has the anti pinch function. The induction glass door cannot be opened normally in case of obstacles or collision of the induction glass door. When it reaches three times, the induction glass door will stop running, and the door leaf will stop opening or closing. In case of such problems, just push the door leaf to the fully open state to recover.

感應玻璃門內部皮帶裝反，導致感應玻璃門關不上。

The inner belt of the induction glass door is installed reversely, resulting in that the induction glass door cannot be closed.

濟南卷簾門廠家提醒，在人通行時，感應玻璃門關閉反而走開時感應玻璃門打開并且打開后不再關閉。遇到這種情況大家都會(huì )認為這是關不上打不開了。這個問題是因為感應玻璃門在安裝或維修時因為技術人員不，把動力皮帶裝反了導致。解決方法是一、調換皮帶上下扣連接，三、控制器故障導致感應玻璃門出現打不開和關不上。

Jinan roller shutter door manufacturer reminds that when people pass through, the sensing glass door is closed, but when they walk away, the sensing glass door is opened and will not be closed after it is opened. In this case, everyone will think that it cannot be closed or opened. This problem is caused by the reverse installation of the power belt during the installation or maintenance of the induction glass door due to the unprofessional technicians. The solutions are: 1. Replace the upper and lower buckle connection of the belt; 3. The sensor glass door cannot be opened or closed due to the controller failure.

遇到這種故障需要調試控制器，如調試不能使其恢復正常，就需要更換控制器了。所以建議大家在進行維護安裝時應找人員，不可因小失大。

In case of such fault, the controller needs to be debugged. If the debugging fails to restore it to normal, the controller needs to be replaced. Therefore, it is suggested that you should find professional personnel when carrying out maintenance and installation, and do not lose money for small gain.

感應玻璃門敞開或關閉的情況下接通電源無反應

When the sensing glass door is open or closed, there is no response when the power is turned on

這情況需要到現場進行檢測，因為出現這個問題的情況比較多，比如雖然插上電源但沒有供電也有可能是控制器死機等原因造成。門道佰分佰技術人員可現場對此問題進行檢測并針對性解決問題。

This situation needs to be detected on site, because there are many cases of this problem. For example, although the power supply is plugged in but there is no power supply, it may also be caused by the controller crash and other reasons. Doorway technicians can detect and solve this problem on site.

遙控器問題，導致感應玻璃門打不開。

There is a problem with the remote control, causing the sensing glass door to not open.

因感應玻璃門遙控器問題導致，用要看解鎖即可。

It is caused by a problem with the remote control of the induction glass door. You can unlock it if you want.

感應玻璃門有關門動作，但無法關閉。

The sensing glass door has closing action, but cannot be closed.

濟南卷簾門廠家認為此種原因是感應器有開門信號輸入，也就是感應器感應范圍內有干擾物存在，比如：太陽光直射、有活動的物體、有不穩定光源等?？梢酝ㄟ^(guò)斷掉感應器信號線來測試是否因為感應器的干擾信號引起感應玻璃門無法關閉。

Jinan roller shutter door manufacturer believes that the reason is that the sensor has a door opening signal input, that is, there are interfering objects within the sensor sensing range, such as direct sunlight, moving objects, unstable light sources, etc. The sensor signal line can be cut off to test whether the inductive glass door cannot be closed due to the interference signal of the sensor.

感應玻璃門始終保持開啟狀態。

The sensing glass door is always open.

引發此感應玻璃門故障的原因可能是感應器損壞，始終有開門信號輸入給感應玻璃門控制器，可能是感應玻璃門遙控器或模式切換開關調整到了敞開狀態，如果是安裝有門禁系統，可能是門禁系統繼電器損壞。

The reason for this induction glass door fault may be that the sensor is damaged. There is always a door opening signal input to the induction glass door controller. It may be that the remote control or mode switch of the induction glass door is adjusted to the open state. If the access control system is installed, it may be that the access control system relay is damaged.

感應玻璃門打不開關不上可能還會(huì )有其他問題導致，這些問題需現場檢測維修。以上就是今天為大家分享的關于問題的相關內容，希望對大家能有所幫助，想要了解更多內容可以電話聯系我們或者關注我們的網站http://www.kalkulackapro.top。

There may be other problems caused by the non opening and closing of the induction glass door. These problems need to be inspected and repaired on site. The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.kalkulackapro.top 。