電動卷簾門需要方便人們或者車輛進進出出的，所以非常需要確保電動卷簾門的性能，電動卷簾門的底邊柔軟，當電動卷簾門的底邊安裝完需要對其功能進行測試驗收，濟南卷簾門廠家建議大家需要注意這些步驟：

The electric roller shutter door needs to be convenient for people or vehicles to enter and exit, so it is very necessary to ensure the safety performance of the electric roller shutter door. The bottom edge of the electric roller shutter door is safe and soft. When the safety bottom edge of the electric roller shutter door is installed, its function needs to be tested and accepted. The Jinan roller shutter door manufacturer recommends that you pay attention to these steps:

一、先將電動卷簾門的急停鍵關閉，開啟電動卷簾門電控箱電源，按壓一次底邊接收器面板學習鍵，檢查信號接收器燈亮。

1、 First close the emergency stop button of the electric roller shutter door, turn on the power supply of the electric roller shutter door electric cabinet, press the bottom receiver panel learning button once, and check that the signal receiver light is on.

二、按壓幾次電動卷簾門的底邊布兜內壓力膠管，信號接收器指示燈出現閃爍表示接收記憶成功，重復按壓底邊壓力膠管，每壓一次接收器就會(huì )燈亮一次，測試信號連接完成。

2、 Press the pressure hose in the safety bottom cloth pocket of the electric roller shutter door several times, and the indicator of the signal receiver flashes, indicating that the receiving memory is successful. Press the bottom pressure hose repeatedly, and the receiver will light up once for each press, and the test signal connection is completed.

三、打開電動卷簾門的電控箱急停鍵，按壓底邊布兜內的壓力膠管，那么電動卷簾門的門體接到信號會(huì )自動上升，正常運轉門體。

3、 Open the electric control cabinet emergency stop button of the electric roller shutter door and press the pressure hose in the bottom cloth bag, then the door body of the electric roller shutter door will automatically rise after receiving the signal, and the door body will operate normally.

四、那么在測試電動卷簾門底邊和使用電動卷簾門過程中，如果發現電控箱無法接收到底邊信號時，需要注意檢查底邊發射器內電池和底邊壓力膠管，如果發現電池耗盡就要更換新電池。如果底邊壓力膠管破損、漏氣，破損漏氣的要進行密封處理，必要時要更換新的底邊壓力膠管。

4、 In the process of testing the safety bottom of the electric roller shutter door and using the electric roller shutter door, if it is found that the electric cabinet cannot receive the safety bottom signal, it is necessary to pay attention to checking the battery in the safety bottom transmitter and the bottom pressure hose. If it is found that the battery is exhausted, replace it with a new battery. If the bottom pressure rubber hose is damaged or leaking, the damaged and leaking rubber hose shall be sealed, and a new safety bottom pressure rubber hose shall be replaced if necessary.

電動卷簾門的底邊驗收和測試就簡單介紹到這里，建議大家選擇的電動卷簾門廠家使用安裝更放心，安裝技術人員更放心有保障。如果還想了解更多電動卷簾門資訊，歡迎大家關注我們http://www.kalkulackapro.top更多信息！

So far is the acceptance and testing of the safety bottom of the electric roller shutter door. It is recommended that the manufacturer of the electric roller shutter door selected be more confident in its use and installation, and that the installation technicians be more confident and secure. If you want to know more about the electric rolling shutter door, please pay attention to us http://www.kalkulackapro.top More information!