電動卷閘門產品調整主要分三部分進行：

The adjustment of electric rolling gate products is mainly carried out in three parts:

機械部分調整

Mechanical part adjustment

（1）限位調整，卷閘門安裝結束后，對門產品的機械部分進行調整，兩步降落的卷閘門一步降位應在距地面1.8m位置。

(1) Limit adjustment: After the installation of the rolling gate is completed, the mechanical part of the door product should be adjusted. The two-step lowering of the rolling gate should be at a height of 1.8m from the ground.

（2）速放裝置試驗，通過手動速放裝置拉鏈下放防火卷閘門，簾桓下降順暢，速度均勻，一步停降到底。

(2) Quick release device test, using manual quick release device zipper to lower the fire shutter, the curtain can descend smoothly and at a uniform speed, stopping and descending to the bottom in one step.

（3）提升裝置試驗，通過手動拉鏈拉起防火卷閘門，拉起全程應順利，停止后防火卷閘門應當靠其自重下降到底。

(3) The lifting device test involves manually pulling up the fire shutter with a zipper. The entire process should be smooth, and after stopping, the fire shutter should be lowered to the bottom by its own weight.

電動部分調整在電動卷閘門兩側安裝的手動按鈕來對門產品進行升、停、降，防火系列的卷閘門可以任意的通過停止按鈕來停止門產品。

The manual buttons installed on both sides of the electric roller shutter are used for adjusting the electric part to lift, stop, and lower the door product. The fireproof series roller shutter can be stopped by the stop button at will.

自動功能調整

Automatic function adjustment

電動卷閘門產品的自動控制方式分有源和無源啟動兩種：無源啟動：門產品可以利用短路線分別短接中限位和下限為的遠程控制，觀察期下落是否順暢，懸停位置是否準確，用萬用表實測中限位和下限位電信號無源回答端子是否導通。有源啟動：門在自動方式調試需要24V電源來供電啟動卷閘門系列產品，觀察下落是否順暢，懸停位置是否準確，用萬用表實測中限位和下限位的電信號的無源回答端子觀察其是否導通。

The automatic control methods of electric rolling gate products are divided into active and passive start: passive start: The door product can use a short circuit to respectively short circuit the middle limit and lower limit for remote control, observe whether the falling period is smooth, whether the hovering position is accurate, and use a multimeter to measure the electrical signals of the middle limit and lower limit to passively answer whether the terminals are conductive. Active start: The automatic debugging of the door requires a 24V power supply to start the rolling gate series products. Observe whether the falling is smooth and the hovering position is accurate. Use a multimeter to measure the passive response terminals of the electrical signals in the middle and lower limits and observe whether they are conductive.