卷閘門遙控器是控制卷簾收起和放下，一些還會有運行中停止和鎖定的功能?，F(xiàn)在卷閘門的使用普及程度較高：家用車庫、店鋪門面等，以這款桃木型卷閘門遙控器為例，它具有普通拷貝遙控器沒有的鎖碼功能，數據再生功能，一鍵智能拷貝功能，因此也就迅速進入民眾視野之中，對于它在使用過程中常遇到的一些故障，我們整理了出來，希望能對使用這類產品的朋友們有一些幫助。

　　The roller shutter remote control is used to control the folding and lowering of the roller shutter, and some also have the function of stopping and locking during operation. Nowadays, the popularity of using roller shutter doors is relatively high, such as in home garages and store storefronts. Taking this peach wood roller shutter remote control as an example, it has lock code function, data regeneration function, and one click intelligent copying function that ordinary copying remote controls do not have. Therefore, it quickly entered the public's field of vision. We have compiled some common faults encountered during its use, hoping to be helpful to friends who use this type of product.

　　一、卷閘門遙控器無法驅動電機或電機轉速慢：可能是線路斷路、電機燒壞、鎖定按鈕沒復位、限位開關動作、負載較大等引起。

　　1、 The remote control of the roller shutter cannot drive the motor or the motor speed is slow: it may be caused by circuit breakage, motor burnout, failure to reset the lock button, limit switch action, high load, etc.

　　處理方法：檢查線路，如有斷路及時接通；更換燒損電機；重復按動幾次鎖定按鈕測試；撥動限位開關滑塊使它脫離微動開關觸點， 并調整微動開關位置；檢查機械部分 有無卡阻，若有則卡阻清理障礙物。

　　Solution: Check the circuit and promptly connect it if there is a break; Replace the burnt motor; Press the lock button several times repeatedly to test; Move the limit switch slider to disengage it from the microswitch contact and adjust the microswitch position; Check if there is any blockage in the mechanical part, and if there is, eliminate the blockage and clean up the obstacles.

　　二、卷閘門遙控器控制失效：原因可能是繼電器（接觸器）觸點粘死、行程微動開關失效或觸片變形、滑塊緊定螺釘松、靠板螺絲松使靠板移位，使滑塊或螺母不能隨絲桿轉動而移動、限位器傳動齒輪破損、按鈕上、下鍵卡死。

　　2、 Remote control failure of the roller shutter: The reasons may be that the relay (contactor) contacts are stuck, the travel micro switch is malfunctioning or the contact piece is deformed, the slider fastening screw is loose, the support plate screw is loose, causing the support plate to shift, making the slider or nut unable to move with the screw rotation, the limit gear transmission wheel is damaged, and the up and down buttons are stuck.

　　處理方法：更換繼電器（接觸器）；更換微動開關或觸片；緊定滑塊螺釘并 使靠板復位；更換限位器傳動齒輪；更換按鈕。

　　Solution: Replace the relay (contactor); Replace micro switches or contacts; Tighten the slider screw and reset the support plate; Replace the transmission gear of the limiter; Replace button.

　　三、卷閘門運動時電機振動或噪聲較大：原因是剎車盤不平衡或斷裂；剎車盤無緊固；

　　3、 The motor vibrates or makes loud noise during the movement of the roller shutter: the reason is that the brake disc is unbalanced or broken; The brake disc is not securely fastened;

　　處理方法：更換剎車盤或重新調整平衡；緊固剎車盤螺母；更換軸承；另外，驅動器每年少要加注潤滑脂，鏈條應經常加注潤滑油，并檢查各部件磨損情況，磨損嚴重的機件要及時維修或更換。

　　Solution: Replace the brake disc or readjust the balance; Tighten the brake disc nut; Replace bearings; In addition, the driver should be lubricated at least annually, and the chain should be regularly lubricated with oil. The wear of each component should be checked, and parts with severe wear should be repaired or replaced in a timely manner.

　　此外，容易造成卷閘門遙控器失靈的一些操作要注意避免：

　　In addition, some operations that may cause the remote control of the rolling shutter to malfunction should be avoided:

　　1、產品長期存放于高溫或者潮濕的環境中，有可能造成產品損壞或壽命縮短；

　　1. Long term storage of products in high temperature or humid environments may cause damage or shorten their lifespan;

　　2、實際使用中，遙控距離變短或者信號響應遲鈍時，請及時更換電池；

　　2. In actual use, if the remote control distance becomes shorter or the signal response is sluggish, please replace the battery in a timely manner;

　　3、在使用時，避開有墻體遮擋的地方。鋼筋混泥土的墻壁對電波的吸收作用較大，對遙控器實際距離的影響更大。

　　3. When using, avoid areas with walls blocking. Reinforced concrete walls have a greater absorption effect on radio waves and a greater impact on the actual distance of the remote control.

本文由濟南富強門業有限公司友情奉獻.更多有關的知識請點擊:http://www.kalkulackapro.top/真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from Jinan Fuqiang Door Industry Co., Ltd. For more related knowledge, please click: http://www.kalkulackapro.top/ Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned